Shark Fin turns the boards for you and it is ergonomically correct. Then it gives the board back to you. You can concentrate on grading instead of material handling. However, you can still touch the board throughout the turn if you wish.

• Pains in your wrists, elbows, shoulders and back should lessen immediately.
• Stay in your job longer with fewer health problems and finish each shift with more energy.
• Sit, stand or walk to grade. You can always touch the board if you want to and you have the opportunity to turn the board to re-grade as many times as necessary.
• Your job is to grade lumber as accurately as possible. We hope Shark Fin makes this job easier for you.

MILL BENEFITS
Fast Pay Back. A 3 Grader Shark Fin System costs approximately $32,000. Let's assume a mill produces 100,000 board feet per shift and lumber is selling at $300.00 per thousand. Working 2 shifts per day, 5 days per week, that's 4 million board feet per month.  If Shark Fin gives you even a 1% "upgrade" that would net $12,000 per month and the system would pay for itself in 3 months. (A 5% upgrade would net $60,000 per month)

• Reduced Grader Injuries and lost man days result in lower WCB assessments. Some firms have paid for their Shark Fin Systems within 3 months by reduced WCB premiums alone. (See Testimonials) 
• Board Damage from marks, oil or grease are prevented with double pulp safe polyurethane lugs and turners.
• Organize your grading table simply, inexpensively and with greatly reduced maintenance.
• Happier, healthier Graders will contribute more to the mills bottom line.

NO RESTRICTIONS

VISIT THE SHARK FIN WEBSITE FOR VIDEOS AND MORE INFORMATION 

TOP

TESTIMONIALS
"I'm proud of this installation and happy to show it off!!"


“The equipment started up Monday morning running at an incredible 10% more production and by the end of the day production was almost double that”. Also, “this was one of the few times where equipment installed has done what was expected of it on start up”.


Charlie Moyer, Project Chief Engineer
Re: Britt Lumber Shark Fin Install, the largest Shark Fin Install in the World. June 2007
BRITT LUMBER/PACIFIC LUMBER
California, USA

"We have installed Shark Fin Board Turners at both of our grading stations, in
September 1998.  We selected the Shark Fin Board Turner because of it's
mechanical simplicity and it's hassle free versatility.  We are happy with this
system, and we strongly recommend it."

"The payback on our board turner project was entirely based on lowering our
WCB Premiums.  With the shark fin, 6 of our senior graders could come back to
work.  The minimum estimated savings for us (at the time we asked Alliance for
the money) is $100,000/year. 

Denis Boulanger
Alliance Forest Products
Mistassini, Quebec

Just a quick note to let you know of our status re: the Shark-Fin Board Turning
System that we installed in November of this year. If you remember there were
some who stated that your system would not work for us because we wanted
your system for four graders working in less than 17' of total space. We pull up to
seven grades and our normal product mix covers 1x3 - 1x6, 2x3 - 2x10. I'm
pleased to report that your system works just fine and we are very happy.  Prior
to installation we had problems with graders going on light duty due to injury. 
Since we've installed the board turners all of our graders have returned to work
and are happy with the system. In fact it's the first time I've seen graders smile
when running 20' 2x10. 

Barry Harley
Special Products Co-Ordinator
Tolko Industries Ltd
Quesnel, BC

We would like to inform you that the shark fin board turner recently installed at
our planer operation has been a great success and accepted by all our lumber
graders.  The system is so simple and maintenance free.  The Worker's
compensation Board visited our plant recently and were very impressed with the
system.   They asked for our permission to take pictures and would also like to
write an article for the monthly magazine.

We at the Lakeland Mills would like to thank you for your assistance during the
installation.

Monty Williams
Lakeland Mills Ltd.
Prince George, BC

From National Hardwood Magazine. 
From an article on Robinson Lumber, Bill Dugger owns
Automated Lumber Handling Co in Lenoir,
NC, who installed the new equipment at Robinson.

He is quoted as saying..."The most important thing that we installed was the
patented Shark Fin Turner...which allows one or two graders to look at up to 60
boards per minute if need be" Dugger said "Before, they were only grading about
40 boards per minute" George Robinson (Owner) says..."We basically have a
state of the art system that allows the Grader to only take the time to look at the
board rather than try to measure the board and do other things.  The grader has
a lot more freedom and can grade more lumber.  For our company to get the
return we needed, we had to get more lumber through our system"  Production
was boosted from 30,000 to 45,000 board feet per day.

“The equipment started up Monday morning running at an incredible 10% more production and by the end of the day production was almost double that”. Also, “this was one of the few times where equipment installed has done what was expected of it on start up”.

Charlie Moyer
Project Chief Engineer
Re: Britt Lumber SharkFin Install, the largest SharkFin Install in the World

QUOTE REQUEST FORMS (Choose Your Location)

CANADA
Soutern BC          Northern BC          The Prairies          Eastern Canada   

USA
Western USA          Central USA          Eastern USA   

TOP